|
Location:
|
Chicago, Illinois
|
Accident Number:
|
CEN25LA116
|
|
Date & Time:
|
March 10, 2025, 18:30 Local
|
Registration:
|
N128AF
|
|
Aircraft:
|
ROBINSON HELICOPTER R44 II
|
Aircraft Damage:
|
Substantial
|
|
Defining Event:
|
Flight control sys malf/fail
|
Injuries:
|
3 None
|
|
Flight Conducted Under:
|
Part 91: General aviation - Business
|
|
|
The pilot reported that he smelled burning rubber followed by the helicopter clutch light coming on for about 5 seconds. The smell intensified and the clutch light came on again. He pulled the clutch circuit breaker and was preparing to land as soon as practical when the helicopter began to vibrate and then he heard a loud bang. The pilot autorotated the helicopter to an open area on a golf course.
The pilot and passengers exited the helicopter uninjured. After landing, the pilot inspected the helicopter and discovered that the tail boom was substantially damaged.
Postaccident examination of the helicopter revealed that the bearing shaft was sheared, and the upper portion of the tension actuator assembly separated. Additionally, the fan shaft separated at the bearing block and part of the fan shaft was stuck/melted inside the bearing shaft.
Review of maintenance logbooks revealed that the bearing shaft was lubricated during 100-hour and annual inspections. However, there was no indication in the maintenance logs that the bearing shaft was lubricated when the fanwheel was replaced. According to the manufacturer’s maintenance instructions, lubrication of the bearing shaft is to be complied with when the fanwheel is removed. The owner stated that he could not recall if the bearing shaft was lubricated when the fanwheel was replaced, but he thinks that it was.
The owner also reported that when he lubricated the bearing shaft, he was not sure if the bearing shaft was being properly lubricated because the grease that was being injected was coming out of the bearing housing. The owner provided a video of him performing the lubrication. The video was shared with a senior technical investigator from the airframe manufacturer. The investigator stated that the tip of the grease syringe was pointed at the bearing race instead of the opening next to the race.
It is likely that the bearing shaft overheated and seized due to inadequate lubrication, which resulted in the failure of the main drive system.
Probable Cause and Findings
The National Transportation Safety Board determines the probable cause(s) of this accident to be:
A failure of the main drive system due to the inadequate lubrication of the bearing shaft.
Findings
Aircraft
|
(general) - Incorrect service/maintenance
|
|
Personnel issues
|
Scheduled/routine maintenance - Maintenance personnel
|
Factual Information
History of Flight
Enroute-cruise
|
Flight control sys malf/fail (Defining event)
|
|
Enroute-cruise
|
Emergency descent initiated
|
|
Landing-flare/touchdown
|
Hard landing
|
On March 10, 2025, about 18:30 central daylight time, a Robinson Helicopter R44 II, N128AF was substantially damaged when it was involved in an accident near Chicago, Illinois. The pilot and both passengers were not injured. The helicopter was operated under the provisions of Title 14 Code of Federal Regulations Part 91 as a sightseeing flight.
The helicopter departed Lansing Municipal Airport (IGQ), Lansing, Illinois, about 17:45. The pilot stated that they flew north, about 25 nm, along the Lake Michigan shoreline to Navy Pier, and then proceeded south back toward IGQ at an altitude of about 1,000 ft above ground level. About 4 nm south of Navy Pier, the pilot reported that he smelled burning rubber followed by the illumination of the helicopter clutch light for about 5 seconds. The smell intensified and the clutch light came on again. The pilot pulled the clutch circuit breaker and prepared to land as soon as practical when the helicopter began to vibrate and then he heard a loud bang. The pilot autorotated the helicopter to an open area on a golf course.
The pilot and passengers exited the helicopter uninjured. After landing, the pilot inspected the helicopter and discovered that the tail boom was substantially damaged.
A postaccident examination of the helicopter found that the C181-3 bearing shaft was sheared, and the upper portion of the C051-2 belt tension actuator assembly was lying on top of the lower drive pully. Additionally, the C007 fan shaft separated at the bearing block and part of the fan shaft was stuck/melted inside the C181-3 bearing shaft.
Review of maintenance logbooks revealed that the C181-3 bearing shaft was lubricated during 100 hour and annual inspections as noted in the Robinson Maintenance Manual Inspection Procedures and Checklist provided by the owner. However, there is no indication in the maintenance logs that the bearing shaft was lubricated when the D174-2 fanwheel was replaced in February 2025. According to the manufacturer’s maintenance instructions, lubrication of the bearing shaft is to be complied with when the fanwheel is removed. The owner stated that he could not recall if the bearing shaft was lubricated when the fanwheel was replaced, but he thinks that it was.
The owner also reported that when he lubricated the bearing shaft, he was not sure if the bearing shaft was being properly lubricated because the grease that was being injected was coming out of the bearing housing. The owner provided the investigator in charge with a video of him performing the lubrication. The video was shared with a senior technical investigator from the airframe manufacturer. The investigator stated that the tip of the grease syringe was pointed at the bearing race instead of the opening next to the race. The investigator in charge provided the owner with the contact information for a technical representative from the airframe manufacturer who could assist with lubrication techniques.
Pilot Information
Certificate:
|
Commercial; Flight instructor
|
Age:
|
30, Male
|
|
Airplane Rating(s):
|
None
|
Seat Occupied:
|
Right
|
|
Other Aircraft Rating(s):
|
Helicopter
|
Restraint Used:
|
3-point
|
|
Instrument Rating(s):
|
Airplane
|
Second Pilot Present:
|
No
|
|
Instructor Rating(s):
|
Helicopter
|
Toxicology Performed:
|
|
|
Medical Certification:
|
Class 2 Without waivers/limitations
|
Last FAA Medical Exam:
|
January 7, 2025
|
|
Occupational Pilot:
|
Yes
|
Last Flight Review or Equivalent:
|
June 2, 2024
|
|
Flight Time:
|
1035.4 hours (Total, all aircraft), 227.7 hours (Total, this make and model), 970 hours (Pilot In Command, all aircraft), 47.6 hours (Last 30 days, all aircraft), 3.7 hours (Last 24 hours, all aircraft)
|
Aircraft and Owner/Operator Information
Aircraft Make:
|
ROBINSON HELICOPTER
|
Registration:
|
N128AF
|
|
Model/Series:
|
R44 II NO SERIES
|
Aircraft Category:
|
Helicopter
|
|
Year of Manufacture:
|
2006
|
Amateur Built:
|
|
|
Airworthiness Certificate:
|
Normal
|
Serial Number:
|
11475
|
|
Landing Gear Type:
|
Skid
|
Seats:
|
4
|
|
Date/Type of Last Inspection:
|
November 20, 2024 Annual
|
Certified Max Gross Wt.:
|
2500 lbs
|
|
Time Since Last Inspection:
|
|
Engines:
|
1 Reciprocating
|
|
Airframe Total Time:
|
2504.3 Hrs at time of accident
|
Engine Manufacturer:
|
Lycoming
|
|
ELT:
|
Not installed
|
Engine Model/Series:
|
IO-540-AE1A5
|
|
Registered Owner:
|
SUMMERSKYZ INC
|
Rated Power:
|
245 Horsepower
|
|
Operator:
|
SUMMERSKYZ INC
|
Operating Certificate(s) Held:
|
None
|
|
Operator Does Business As:
|
Commercial Air Tour Operations
|
Operator Designator Code:
|
|
Meteorological Information and Flight Plan
Conditions at Accident Site:
|
Visual (VMC)
|
Condition of Light:
|
Dusk
|
|
Observation Facility, Elevation:
|
KORD, 672 ft msl
|
Distance from Accident Site:
|
19 Nautical Miles
|
|
Observation Time:
|
18:51 Local
|
Direction from Accident Site:
|
305°
|
|
Lowest Cloud Condition:
|
|
Visibility:
|
10 miles
|
|
Lowest Ceiling:
|
Broken / 25000 ft AGL
|
Visibility (RVR):
|
|
|
Wind Speed/Gusts:
|
11 knots / 19 knots
|
Turbulence Type Forecast/Actual:
|
None / None
|
|
Wind Direction:
|
210°
|
Turbulence Severity Forecast/Actual:
|
N/A / N/A
|
|
Altimeter Setting:
|
29.61 inches Hg
|
Temperature/Dew Point:
|
18°C / 0°C
|
|
Precipitation and Obscuration:
|
No Obscuration; No Precipitation
|
|
|
Departure Point:
|
Lansing, IL (IGQ)
|
Type of Flight Plan Filed:
|
None
|
|
Destination:
|
Lansing, IL (IGQ)
|
Type of Clearance:
|
None
|
|
Departure Time:
|
17:45 Local
|
Type of Airspace:
|
Class G
|
Airport Information
Airport:
|
Lansing Municipal IGQ
|
Runway Surface Type:
|
|
|
Airport Elevation:
|
619 ft msl
|
Runway Surface Condition:
|
Dry
|
|
Runway Used:
|
|
IFR Approach:
|
None
|
|
Runway Length/Width:
|
|
VFR Approach/Landing:
|
Precautionary landing
|
Wreckage and Impact Information
Crew Injuries:
|
1 None
|
Aircraft Damage:
|
Substantial
|
|
Passenger Injuries:
|
2 None
|
Aircraft Fire:
|
None
|
|
Ground Injuries:
|
N/A
|
Aircraft Explosion:
|
None
|
|
Total Injuries:
|
3 None
|
Latitude, Longitude:
|
41.7777,-87.5813
|
Administrative Information
Investigator In Charge (IIC):
|
Abraham, Laura
|
|
Additional Participating Persons:
|
Tracy Mayo; FAA; Chicago, IL
|
|
Original Publish Date:
|
November 12, 2026
|
|
Last Revision Date:
|
|
|
Investigation Class:
|
Class 3
|
|
Note:
|
The NTSB did not travel to the scene of this accident.
|
|
Investigation Docket:
|
https://data.ntsb.gov/Docket?ProjectID=199828
|
READ MORE ROTOR PRO: https://justhelicopters.com/Magazine
WATCH ROTOR PRO YOUTUBE CHANNEL: https://buff.ly/3Md0T3y
You can also find us on
Instagram - https://www.instagram.com/rotorpro1
Facebook - https://www.facebook.com/rotorpro1
Twitter - https://twitter.com/justhelicopters