NTSB Final Report: Chicago, IL

Created 5 hours ago
by Admin

Tags: Chicago Illinois NTSB Report
Categories: Press Releases
Views: 82

Location:

Chicago, Illinois

Accident Number:

CEN25LA116

Date & Time:

March 10, 2025, 18:30 Local

Registration:

N128AF

Aircraft:

ROBINSON HELICOPTER R44 II

Aircraft Damage:

Substantial

Defining Event:

Flight control sys malf/fail

Injuries:

3 None

Flight Conducted Under:

Part 91: General aviation - Business

 

 

The pilot reported that he smelled burning rubber followed by the helicopter clutch light coming on for about 5 seconds. The smell intensified and the clutch light came on again. He pulled the clutch circuit breaker and was preparing to land as soon as practical when the helicopter began to vibrate and then he heard a loud bang. The pilot autorotated the helicopter to an open area on a golf course.

The pilot and passengers exited the helicopter uninjured. After landing, the pilot inspected the helicopter and discovered that the tail boom was substantially damaged.

Postaccident examination of the helicopter revealed that the bearing shaft was sheared, and the upper portion of the tension actuator assembly separated. Additionally, the fan shaft separated at the bearing block and part of the fan shaft was stuck/melted inside the bearing shaft.

Review of maintenance logbooks revealed that the bearing shaft was lubricated during 100-hour and annual inspections. However, there was no indication in the maintenance logs that the bearing shaft was lubricated when the fanwheel was replaced. According to the manufacturer’s maintenance instructions, lubrication of the bearing shaft is to be complied with when the fanwheel is removed. The owner stated that he could not recall if the bearing shaft was lubricated when the fanwheel was replaced, but he thinks that it was.

The owner also reported that when he lubricated the bearing shaft, he was not sure if the bearing shaft was being properly lubricated because the grease that was being injected was coming out of the bearing housing. The owner provided a video of him performing the lubrication. The video was shared with a senior technical investigator from the airframe manufacturer. The investigator stated that the tip of the grease syringe was pointed at the bearing race instead of the opening next to the race.

It is likely that the bearing shaft overheated and seized due to inadequate lubrication, which resulted in the failure of the main drive system.

Probable Cause and Findings

The National Transportation Safety Board determines the probable cause(s) of this accident to be:

A failure of the main drive system due to the inadequate lubrication of the bearing shaft.

Findings

Aircraft

(general) - Incorrect service/maintenance

Personnel issues

Scheduled/routine maintenance - Maintenance personnel

Factual Information

History of Flight

Enroute-cruise

Flight control sys malf/fail (Defining event)

Enroute-cruise

Emergency descent initiated

Landing-flare/touchdown

Hard landing

On March 10, 2025, about 18:30 central daylight time, a Robinson Helicopter R44 II, N128AF was substantially damaged when it was involved in an accident near Chicago, Illinois. The pilot and both passengers were not injured. The helicopter was operated under the provisions of Title 14 Code of Federal Regulations Part 91 as a sightseeing flight.

The helicopter departed Lansing Municipal Airport (IGQ), Lansing, Illinois, about 17:45. The pilot stated that they flew north, about 25 nm, along the Lake Michigan shoreline to Navy Pier, and then proceeded south back toward IGQ at an altitude of about 1,000 ft above ground level. About 4 nm south of Navy Pier, the pilot reported that he smelled burning rubber followed by the illumination of the helicopter clutch light for about 5 seconds. The smell intensified and the clutch light came on again. The pilot pulled the clutch circuit breaker and prepared to land as soon as practical when the helicopter began to vibrate and then he heard a loud bang. The pilot autorotated the helicopter to an open area on a golf course.

The pilot and passengers exited the helicopter uninjured. After landing, the pilot inspected the helicopter and discovered that the tail boom was substantially damaged.

A postaccident examination of the helicopter found that the C181-3 bearing shaft was sheared, and the upper portion of the C051-2 belt tension actuator assembly was lying on top of the lower drive pully. Additionally, the C007 fan shaft separated at the bearing block and part of the fan shaft was stuck/melted inside the C181-3 bearing shaft.

Review of maintenance logbooks revealed that the C181-3 bearing shaft was lubricated during 100 hour and annual inspections as noted in the Robinson Maintenance Manual Inspection Procedures and Checklist provided by the owner. However, there is no indication in the maintenance logs that the bearing shaft was lubricated when the D174-2 fanwheel was replaced in February 2025. According to the manufacturer’s maintenance instructions, lubrication of the bearing shaft is to be complied with when the fanwheel is removed. The owner stated that he could not recall if the bearing shaft was lubricated when the fanwheel was replaced, but he thinks that it was.

The owner also reported that when he lubricated the bearing shaft, he was not sure if the bearing shaft was being properly lubricated because the grease that was being injected was coming out of the bearing housing. The owner provided the investigator in charge with a video of him performing the lubrication. The video was shared with a senior technical investigator from the airframe manufacturer. The investigator stated that the tip of the grease syringe was pointed at the bearing race instead of the opening next to the race. The investigator in charge provided the owner with the contact information for a technical representative from the airframe manufacturer who could assist with lubrication techniques.

Pilot Information

Certificate:

Commercial; Flight instructor

Age:

30, Male

Airplane Rating(s):

None

Seat Occupied:

Right

Other Aircraft Rating(s):

Helicopter

Restraint Used:

3-point

Instrument Rating(s):

Airplane

Second Pilot Present:

No

Instructor Rating(s):

Helicopter

Toxicology Performed:

 

Medical Certification:

Class 2 Without waivers/limitations

Last FAA Medical Exam:

January 7, 2025

Occupational Pilot:

Yes

Last Flight Review or Equivalent:

June 2, 2024

Flight Time:

1035.4 hours (Total, all aircraft), 227.7 hours (Total, this make and model), 970 hours (Pilot In Command, all aircraft), 47.6 hours (Last 30 days, all aircraft), 3.7 hours (Last 24 hours, all aircraft)

Aircraft and Owner/Operator Information

Aircraft Make:

ROBINSON HELICOPTER

Registration:

N128AF

Model/Series:

R44 II NO SERIES

Aircraft Category:

Helicopter

Year of Manufacture:

2006

Amateur Built:

 

Airworthiness Certificate:

Normal

Serial Number:

11475

Landing Gear Type:

Skid

Seats:

4

Date/Type of Last Inspection:

November 20, 2024 Annual

Certified Max Gross Wt.:

2500 lbs

Time Since Last Inspection:

 

Engines:

1 Reciprocating

Airframe Total Time:

2504.3 Hrs at time of accident

Engine Manufacturer:

Lycoming

ELT:

Not installed

Engine Model/Series:

IO-540-AE1A5

Registered Owner:

SUMMERSKYZ INC

Rated Power:

245 Horsepower

Operator:

SUMMERSKYZ INC

Operating Certificate(s) Held:

None

Operator Does Business As:

Commercial Air Tour Operations

Operator Designator Code:

 

Meteorological Information and Flight Plan

Conditions at Accident Site:

Visual (VMC)

Condition of Light:

Dusk

Observation Facility, Elevation:

KORD, 672 ft msl

Distance from Accident Site:

19 Nautical Miles

Observation Time:

18:51 Local

Direction from Accident Site:

305°

Lowest Cloud Condition:

 

Visibility:

10 miles

Lowest Ceiling:

Broken / 25000 ft AGL

Visibility (RVR):

 

Wind Speed/Gusts:

11 knots / 19 knots

Turbulence Type Forecast/Actual:

None / None

Wind Direction:

210°

Turbulence Severity Forecast/Actual:

N/A / N/A

Altimeter Setting:

29.61 inches Hg

Temperature/Dew Point:

18°C / 0°C

Precipitation and Obscuration:

No Obscuration; No Precipitation

 

Departure Point:

Lansing, IL (IGQ)

Type of Flight Plan Filed:

None

Destination:

Lansing, IL (IGQ)

Type of Clearance:

None

Departure Time:

17:45 Local

Type of Airspace:

Class G

Airport Information

Airport:

Lansing Municipal IGQ

Runway Surface Type:

 

Airport Elevation:

619 ft msl

Runway Surface Condition:

Dry

Runway Used:

 

IFR Approach:

None

Runway Length/Width:

 

VFR Approach/Landing:

Precautionary landing

Wreckage and Impact Information

Crew Injuries:

1 None

Aircraft Damage:

Substantial

Passenger Injuries:

2 None

Aircraft Fire:

None

Ground Injuries:

N/A

Aircraft Explosion:

None

Total Injuries:

3 None

Latitude, Longitude:

41.7777,-87.5813

Administrative Information

Investigator In Charge (IIC):

Abraham, Laura

Additional Participating Persons:

Tracy Mayo; FAA; Chicago, IL

Original Publish Date:

November 12, 2026

Last Revision Date:

 

Investigation Class:

Class 3

Note:

The NTSB did not travel to the scene of this accident.

Investigation Docket:

https://data.ntsb.gov/Docket?ProjectID=199828

 READ MORE ROTOR PRO: https://justhelicopters.com/Magazine

WATCH ROTOR PRO YOUTUBE CHANNEL: https://buff.ly/3Md0T3y

You can also find us on

Instagram - https://www.instagram.com/rotorpro1

Facebook - https://www.facebook.com/rotorpro1

Twitter - https://twitter.com/justhelicopters